Chapter VI: Part 6

At the commencement of this article, it was stated that silicic acid, or silica, could be made soluble in water. Some very interesting experiments were performed by the late Dr. Graham, Master of the Mint, which gave rise to the discovery of the process of dialysis. If some silicate of soda be mixed with water, so that not more than 5 per cent. of silica be in the solution (rather less is better), and if some hydrochloric acid be then added in sufficient quantity to make the liquid distinctly acid, and the mixture be placed in a dialyzing apparatus, the chloride of sodium formed by the union of the chlorine of the hydrochloric acid with the sodium of the silicate of soda will pass out through this dialyzing membrane, leaving hydrated silica behind, which will remain in solution in the water with which the silicate was mixed. The dialyzing apparatus is constructed in the following manner; a sort of tambourine ring is made with gutta percha, in place of wood, from 8 to 10 inches or even more in diameter, the depth, being about 2 inches. Another ring of gutta percha, of about an inch deep or even less, is made so as to fit tightly outside the tambourine; a piece of vegetable parchment is then moistened and placed over the tambourine, and the thinner ring is pressed over it, so as to secure it tightly. This is the dialyzing vessel, and it is into this that the mixture of silicate and hydrochloric acid must be put. The solution should not be more than an inch deep in the dialyzing vessel, which is then made to float upon distilled water in a larger vessel of suitable size. The distilled water should be changed every day, until no precipitate can be obtained in it with nitrate of silver, and when this point is arrived at, all the chloride of sodium will have passed through the vegetable parchment into the larger vessel of water, and nothing but silicic hydrate will remain behind in solution. If this liquid be allowed to stand for some time, it will gelatinize, and later on the jelly will contract, becoming extremely hard, so that lumps of it, when broken, will in their fracture resemble that of flint. No doubt, at some future period, some one will discover a method of rendering this condition of silica useful in the arts.

Soluble silicates are very useful as detergents. A small quantity of silicate of soda mixed with hard water renders it valuable for washing purposes. Silicate of soda is also used in the manufacture of the cheaper kinds of soap. We can hardly speak of it as an adulteration, because it renders the soap with which it is combined much more powerful in its cleansing action. I suggest to those interested in the application of science to the arts, that this subject will no doubt well repay experimental investigations.

It is much to be wished that those engaged in this branch of art and manufacture, and who have some knowledge of chemistry, would turn their attention to getting a better and more perfect method of making coloured pot-metal glass. I have been engaged for some time, and still am engaged, in experiments to effect this object. But inasmuch as my engagements are very numerous, and I cannot give the proper time to it I desire, I therefore take the liberty of suggesting to others the ways in which I am working, that they may be able to arrive at good results more speedily probably than I shall be able to do. If sulphate of copper be mixed with silicate of potash, silicate of copper will be precipitated. Now, if this be carefully washed and dried, it will be a silicate of a definite composition, and I propose to use such silicates as these with ordinary glass mixtures, in order to impart the particular colour which the oxide employed has been already described as giving to the glass. Silicate of manganese is prepared in a similar way to the silicate of copper; silicate of cobalt, and other silicates, can be used as staining materials for colouring glass. These mixed in due proportion would give tints, and would, I do not feel the slightest doubt, produce colours with much greater certainty than they are now produced, and tints hitherto unknown could be made to the great benefit of the glass-painter.

FURNITURE AND WOODWORK.

BY J. H. POLLEN, M.A., South Kensington Museum.

I propose in the following pages to give some account of the materials used in making furniture, and of the arts applied to its decoration. From the earliest ages of society, when men moved about in tribes, they had in their tents of camels' hair simple necessaries, such as their wants required. Before people were gathered into distinct nations, or cities built with walls and gates, there were still certain human wants that must needs be supplied; and the objects that were needed to enable mankind to live with convenience and decency were found in their furniture. To this very day we may see Arab tribes wandering over sunny deserts, seeking pasturage, sowing here and there an acre of wheat or barley, or gathering dates. Their camels and dromedaries are their waggons, their horses are their friends, their families and those of others that make up their tribe are their only nationality. Yet they furnish in some sort the temporary homes which they shift from one spring of water to another, as the patches of grass or grain grow up and ripen. Their chief wants are, a cloth strained over three staves to make a house, mats or carpets to lie on, a few bowls to cook in, saddles of wood, and a few baskets or chests, made of light sticks fastened together.

In later periods of history and in more conventional states of society, we shall find this primitive type of furnishing carried out with growing splendour. In the West and in the East, in ancient and mediA|val times, great rulers, though constantly in the saddle, have been followed by enormous trains of camp followers, by whom costly furniture, hangings, vessels of plate, and other luxuries, have been carried for the convenience of the leaders and warriors of moving hosts; and of course this splendour was the measure of the state and magnificence kept at home. The wealth or feudal state, shown in the furniture of old castles and palaces, extended not only to halls and rooms, but to dresses, and armour, weapons, the furniture of horses, tents, and other objects that could be carried on distant expeditions.

Ancient nations have been as well, and more splendidly, if less conveniently, provided with furniture for their houses than modern ones. It happens that there are distinct records of many kinds, showing what wealth and elaborate decoration some of the oldest races, such as the Assyrians, the Egyptians, the Persians, and the Greeks, bestowed on their thrones, beds, chairs, and chariots. Beds of silver and gold are mentioned in Esther i., and the curtains of the bed of Holofernes were covered with a canopy of purple and gold, with emeralds and precious stones (Judith x. 19; Esther i.). Modern princes in India continue to devote their jewels and gold to similar uses. It must be borne in mind also, that this kind of splendour is an investment of property in times and countries in which banks, insurance offices, government funds, and other organized means of investing money are unknown.

Silver, if not gold, has been used occasionally, not only in the East, but in Europe, for seats, tables, even the frames of pictures and mirrors. The royal apartments in Whitehall were completely mounted with hammered and filagree silver furniture in the seventeenth century. Carlyle records of Frederick the Great, that silver ornaments were kept in his palace, and turned to account under the exigencies of war. But of furniture generally, wood is the readiest and most proper material. It is handy, easily worked, light to carry about, and may be manufactured with or without decorations of carved work, or of any other kind. Hence, in giving an account, whether historical or mechanical, of furniture, I class it under the more general head of woodwork. Any other materials, either for the framing or ornamentation of furniture, are exceptional. The remarks now to be submitted to the reader will refer to wood that is manufactured, though I shall not enter on the interesting subject of wood structure, which has been applied to such noble and elaborate uses, and of which such splendid monuments of many periods still remain for us to study.

Most of the methods used for decorating woodwork made up into furniture are still in regular use, and the processes of putting it together are the same as they have always been. The reader may satisfy himself on this point any day by a walk in the Egyptian rooms and in the Nineveh galleries of the British Museum. In both these sections of that wonderful collection, there are remains of woodwork and of furniture, made of wood three or four thousand years old, such as stools, chairs, tables, head-rests or pillows, workmen's benches of Egyptian manufacture, fragments less complete of Nineveh make that have been portions of various utensils, and precious articles of sculptured and inlaid ivory that have been inserted into thrones and chariots. These pieces of furniture have been mortised together, or joined by dowels, dovetailed at the angles, glued, nailed, or, in short, made up by the use of several of these methods of junction at the same time. And no great changes have been introduced in the various ways of ornamenting furniture. The Egyptian woodwork was painted in tempera, and carefully varnished with resinous gums. It was inlaid with ebony and other woods, carved, gilt and, perhaps, sparingly decorated with metal ornaments. The Greeks inlaid chests and tables with carved ivory and gold, sometimes relieved with colour. The Romans, who made much furniture of bronze, cast, inlaid, damascened and gilt, made much more in wood, which they stained, polished, carved, and inlaid. MediA|val furniture was put together with mortises, tenons and glue, and was gilt and painted; the painting and gilding being laid on a ground prepared with the utmost care, and tooled and ornamented in the same way that bookbinders ornament leather. At a later period, a beautiful manufacture was carried on in various parts of Italy; a sort of mosaic in very hard stone, such as agate, lapis lazuli, and other precious materials. The Italians also used these beautiful stones inlaid in ebony. But the furniture most valued in modern times has been that which owes its name to Boulle, a French artist of the seventeenth century; and the marquetry, or wood mosaic surface decoration, which reached so high a standard of excellence during the last thirty years of the eighteenth century in France.

The former of these two classes of manufacture made, if not originated, by Boulle (and I am inclined to think that he was not the first maker), was a marquetry, or surface decoration, not composed of various woods, but of tortoiseshell and brass, with the occasional introduction of other metal, and with metal enamelled in blue and other colours. The materials principally in use, however, in Boulle marquetry are tortoiseshell and brass. In the older work, viz. that of the seventeenth century, the tortoiseshell is dark, and left in its natural hue. In later Boulle, called new Boulle, the tortoiseshell is reddened by colour, or by gilding laid under it. There is much grace and variety in the delicate arabesque designs in which one material is inlaid in the other. Parts of the surfaces are sometimes diapered, as a contrast to the free lines and curves of other parts. The inlaid surface of Boulle work is framed in by borders, cornices, or handles of brass or gilt bronze, giving a massive architectural character to the whole.

Thus if we look back to the history of furniture, not only will every kind of splendid material be found devoted to the manufacture or decoration of it, but the best art too of many different periods that money could command. It is in the late times of antiquity, and since the period of the Renaissance in modern times, that works of art have been kept on shelves or gathered into galleries. Many works of great masters, such as the chest of Cypselus, and the chairs of the great statues of ivory and gold, were prepared for celebrated shrines and temples in the cities of Greece. It was but the excessive wealth of great patricians in Rome and Constantinople that led to their becoming collectors, whether of sculpture, painting, or sumptuous silver plate. The chief object of rich and accomplished men in most ages of luxury and refinement has been, to make the house, its walls, ceilings, floors, and necessary or useful furniture, costly and beautiful. It was the same in the days of Donatello, Raphael, Cellini, and Holbein. Chests and trays were painted, together with gems, dies, brooches; table plate was modelled and chiselled; while chairs of wrought steel, or tables, cabinets, and other pieces of rich furniture, were either designed or carried into execution by these masters with their pupils and followers. In some instances, as, e.g., in that of the famous Pomeranian cabinet, in the Kunst Kammer in Berlin, a long list has been preserved of artists and craftsmen of note in their day, who combined to produce monumental examples of actual room furniture.

It cannot be denied that though great pains are taken and much expense is incurred in modern furnishing, the habits of the day lead rather to the search for comfort than for grace or beauty; and convenience rather than intrinsic value or artistic excellence. Nevertheless, a certain amount of decency and splendour is indispensable in both receiving and sleeping rooms; and though a house really well, that is beautifully, furnished is of rare occurrence, this is not for want of serious efforts, nor altogether to be laid to the account of unwillingness to spend money for such a purpose. Whether the "art of furnishing" or the desire to have what people require for use in their houses more becoming and beautiful, be a rising influence or not, it is certain that the "fancy" or ornamental furniture trade is of large and increasing importance, corresponding to the increased size and cost of modern London and country houses, compared with those built during the reigns of William III. and George IV. Every tradesman who has the pretension to repair chimney-pots, to whitewash, or paint house-fronts, ceilings, or offices, writes up the word "decorator," on his shop-front.

THE QUALITIES REQUIRED IN FURNITURE.

We may consider furniture under two broad divisions, that which is made to be handled and moved about, and that which is for use but not meant to be handled or moved. We may add a third division in the actual fixtures of the house, made by the joiner and meant to be ornamental fittings or completions to the builder's and carpenter's work.

Under the first head will be included light tables, chairs, couches, and other movable objects; under the second, cabinets, book-shelves, frames, mirrors, and so on; under the third head come flooring, panelling, window shutters, door-frames, stair-rails, &c.

1. CHAIRS, TABLES, ETC.

The essential points in a well-made chair are comfort, lightness, and strength. Of course, as men and women are pretty much of the same proportion all over the world, chairs, of which the seat is about the height of the lower process of the human knee-joints, must be of the same height, or but slightly varied, in every country. From the habit that so many persons have of throwing their whole weight back and, as we are told, in some countries, of balancing their persons on the back legs of their chairs and inclining their legs in the direction of the chimneypiece, there is often an immense strain on the back joints of chairs. Whether we lean back or swing on them, the junction of the seats of chairs with the backs is always subject to severe trials; and on no article of furniture in common use is such good joinery required. It is worth while to look at the old wall paintings of the Egyptians, as they are given in Rossellini and the great French book of the 'Description de l'Egypte,' to see what capital workmanship those most ancient carpenters bestowed on their chairs. Those of the best and oldest periods are without connecting bars to the legs before or behind, all the strength of the construction being centred in the excellence of the joints of the seat with the back and legs; and in modern workshops, the highest skill is applied to ensure strength in these points of junction. If the wood is thoroughly dry, the mortises and tenons fitting perfectly, and the glue good, the different parts are so wedded together that the whole structure becomes one piece, as if nature had made a vegetable growth in that fashion, all the fibres of which have continuous and perfect contact with each other. If, however, there is a deficiency in any of these conditions, these joints fail. If the wood shrinks, or the tenons do not fit the mortises all through, or the glue is deficient, these various portions speedily come to pieces. Sofas, couches, and stuffed chairs are so much more massive in construction that there need be no risk of such a kind of disintegration.

The members of which a chair is made up may be either turned in the lathe, or left massive enough to allow of carving on the legs, backs, or round the framework of the seat. Turned work can be lightly inlaid with ivory, as that of ancient Egypt, painted, gilt, or mounted (lightly also) with metal.

The subjects of the carving may be either figures of men, horses, lions, or the heads and legs of such animals, acanthus leaves, and arabesques. Many of these ornaments have been used from ancient times, and revived at various historical periods. For modern rooms the lightest construction is most in place, and therefore carving should be compact in composition and delicate in execution, without prominences or undercutting that would interfere with comfort or be liable to breakage.

A certain architectural character is given to chairs by cutting flutings down the legs, or by borrowing other slight details from architecture. The upholstery of chairs will always be their most noticeable decoration, and this applies still more to lounging chairs and couches of all shapes and sizes, as the framework of them is so much less observable in proportion to their upholstered surfaces.

Tables, lampstands, &c., being generally, though not always, meant to be moved about, require as light a construction as is consistent with strength. The surface of all but small tables is beyond the dimensions of a single plank of wood. The outer and inner portions of a log or plank are of different fineness of grain, contain varying proportions of sap, and shrink in different degrees. Single planks of wood, therefore, can only be exceptionally used for table tops. Generally, they are made up of portions of planks selected with great care, grooved on the edges, with a tongue or slice of wood cut the cross way of the grain, uniting the planks about the middle of their thickness; the edges are then firmly glued together. If the surface is to be of wood which can be procured in large pieces of straight or continuous grain, such as mahogany, the wood is solid throughout; if of some rare wood or rare figured graining, such as the roots or wens of oak, this ornamental surface is laid on in thin slices with glue and heavy pressure. This is known as _veneering_. The surface is sometimes inlaid with ivory, metal, mother-of-pearl, slices of agate and other substances, as in the Boulle or marquetry work already alluded to.

The frame of the table is either a deep rail not far within the edge, or a thick pillar or leg or several legs collected, mortised into a broad expanding foot and supporting a spreading framework above, to which the top itself can be fastened, and stretching far enough all round in the direction of the edges to give a firm support.

The decoration of the top can only be superficial if the table is for use, and any decoration by carving, piercing, and so on, must be confined to the framework and the supports. These parts can be, and have been at all times decorated as the framework of chairs, and by very much the same kinds of ornament.

To tables of more modern periods, little galleries of pierced work or of tiny balustrades are sometimes added. They belong to the age of porcelain collectors, hoops, broad coat-skirts, and tea-parties, and are intended to save delicate wares from being swept to the ground. Side tables, and such as are made to support heavy objects, can be treated with more massive frame work and supports, and the carving and decorations will be bolder and larger accordingly.

2. CABINETS, ETC.

I will proceed to the second division of furniture, cabinets, bookcases, and other standing objects, which are more or less immovable. But shelves and china trays must be placed in secure parts of the room, if they are not actually fastened to the wall. The former must be strong to support the great weights laid upon them, and the supports or framework, which is all that would be seen, may be carved or decorated with surface or applied metal ornament. On a large scale, fittings of this kind belong rather to architectural woodwork. China holders, whether placed on the ground or fixed against a wall, are properly treated with shelves quaintly shaped on plain and light, pierced galleries or gilt decorations corresponding with the apparent lightness of pieces of porcelain. The wood and lac work cabinets of the Chinese; and the complicated, but not ungraceful, gilt mirror frames and flourishing acanthus work of the Italians, French, and Germans, of the last century, seem specially suited for showing off this gay and fragile material. The collector proper will probably place his treasures under glass, and with little regard to the framework of his cases. Here china and china stands are treated only as decorations.

As to cabinets, they are the most precious, if not the most useful of all pieces of furniture. They have generally been intended to hold family treasures, are not required to be moved, and have therefore been the richest and most decorated objects in the room. Cabinets are the legitimate descendants of the chests of former days containing bridal outfits and trinkets, or plate, jewellery, and other valuables. They were carried from town to country, from grange to castle. About the beginning of the sixteenth century, the personal habits of great men became less nomad, and their chests were no longer liable to be packed and moved away. These receptacles were mounted on stands at which height the lids could not be lifted, and doors were substituted. Drawers took the place of shelves or compartments, and every sort of ingenuity was applied to make these pieces of furniture quaint and splendid inside and out.

As to shape, it is contrary to their purpose of convenience and interior capacity, to make cabinets, cupboards, or other receptacles, with showy and spreading architectural details, such as cornices, architraves, columns, pediments, and the like. All these parts, which are laborious and costly in construction, are so many additions to its size, and make no more room inside to compensate for this expenditure. Cabinets should, in propriety, be as big and convenient inside as their size would lead us to expect.

On the other hand, the many fine examples made in the sixteenth and seventeenth centuries in this country, Holland, Germany, France or elsewhere, have been generally intended for rooms larger, higher, and with fewer pieces of furniture in them than those of our modern houses, not to speak of the massiveness of fireplaces and fittings with which they were in character. It is their age, and the connection, which we cannot help tracing, with old houses and bygone generations which give architectural cabinets an interest now.

In construction, the skill of the cabinet maker will be shown in the neat and convenient arrangement of drawers of various depths and sizes, shelves or repositories, so contrived as to turn the entire internal space to account. The most curious contrivances are often found in old German, English, and French cabinets, bureaux, secrA(C)taires, and other varieties of this kind of furniture. Pediments, capitals of columns, and other parts of architectural fronts are made to open, and secret drawers stowed away with an ingenuity almost humorous. It is upon the fronts and stands that the skill of great masters of the craft has been bestowed. The large wardrobes, or "armoires," of Boulle are examples of great inventive and designing power, as well as the marquetry of Riesener and David, and the chiselled metal-work of Berain, GouthiA"re, and that of many English artists.

As in past times, and so in our own, it is on cabinets that the real triumphs of the cabinet maker's art are displayed.

3. FIXED WOODWORK.

Thirdly, the joiner's and cabinet maker's art plays an important part in the fixed furniture of the house, and the woodwork, such as flooring, doors and door-frames, panelling, chimneypieces, with the complementary decorations of hangings, whether tapestry, silk, or the more humble material of paper.

In this last division of furniture the work is that of joinery. There is no great demand for constructive strength, as the work is fixed to walls; but as doors and shutters are swung to and fro continually, and subject to jars and strains, their stiles and rails, upright and cross-framing members, as well as the panelling that fills them, require well-seasoned timber and the most accurate workmanship: without these conditions the joints open, the panels shrink from the grooves in which the edges are held, and split, while the frame itself, if of unseasoned material, 'buckles' or twists, so that the door or shutter will no longer shut flat in its frame.

Panelling and fireplaces are, however, opportunities for the display of carving, inlaying, and gilding. The reader has seen carved room panelling, probably, in many old houses. In some of the municipal 'palaces' in Flanders, e.g. in Bruges, and in the old rooms of the Louvre in Paris, carved panelling of the utmost grace and perfection, some of it in groups of life-sized portrait figures, may be studied by the tourist.

Of work so rich and costly as this wood sculpture, it is perhaps hopeless to speak with reference to our modern houses, and in connection with the manufacture of furniture in this country, at least on any large or general scale of application. Still as such work, confined to the composition of fireplaces or sideboard backs, is still sculptured by Italian and French carvers, and has been sent to Universal Exhibitions of recent years, it must be considered a possible effort for our great employers of skilled labour.

The panelling of wall surfaces will be divided into larger or smaller reticulations or framework, with some reference to the size of the room, that is to say, that very large and lofty rooms will not bear the smaller subdivision of space and delicate moulding lines which are so general in panelling of mediA|val or very early Tudor houses, and which are in keeping on walls of moderate size. Any inlaying or variety of woods should be used on walls with great discretion.

So far, then, on the general consideration of the work, which it is the business of the furniture maker to produce. In theory, it is his object to satisfy daily wants and necessities in the most convenient, useful, and agreeable way.

The difference between rudeness and refinement in daily habits consists in putting first order and propriety, then comeliness and cheerfulness into our homes and habits. There is so much to be borne and to be done merely that we may live, so many contradictions to natural inclination meet us on all sides, that we look for repose, and some moderate satisfaction to the natural desire of the eye, in that which meets it, and must meet it, so constantly. This satisfaction is beauty, or some measure of it, or what we have grown to take for beauty. As the eye is more exercised, the mind more informed, and becomes a better monitor or corrective to the eye, so we get less satisfied with much that passes for beauty, and so, on the other hand, we find it out in objects in which it is commonly or often passed over.

MANUFACTURE.

A return prepared by the Commissioners for the Paris Exhibition, in 1867, gave the following as the number of manufacturers engaged in London in "the several branches of the fancy furniture trade."

Cabinet makers 812
Upholsterers 486
Carvers and gilders 342
French polishers 142
Cabinet carvers, inlayers, and liners 108
Bedstead-makers 43
Chair, sofa, and stool-makers 252

Wood and cabinet wares were exported (in 1865) to the value of 289,887_l._, and imported to the value of 128,925_l._[5]

[5] Cat. Brit. Section Exhibition, 1867, Introduction, p. 61.

The highest efforts of the trade are concentrated in a few large establishments in London and the great cities, which have their own cabinet makers, carvers, upholsterers, &c., on their premises. In some instances, one piece of furniture may pass through the hands of several branches of the manufacture. I may choose a few names of makers who presented their works in Paris in 1867 in alphabetical order, e.g. Messrs. Collinson and Locke, Crace, Dyer and Watts, Gillow, Herring, Holland, Howard, Hunter, Ingledew, Jackson and Graham, Morant, Trollope, Wertheimer, Wright and Mansfield. The larger of these establishments are supplied with steam machinery, and all the work that can possibly be executed by mechanical agency is prepared by these engines, leaving only the most costly operations to be executed by hand.

It is the province of the carpenter to put together simple woodwork; that which is an actual part of architecture, such as boxes, chests, benches, seats, shelves, and so forth as require only good material and neatness of hand in execution. The joiner and cabinet maker include this amount of skill as a foundation for their accomplishments, as a sculptor can block out a statue and a painter grind his colours, work, however, which in ordinary practice is handed over to assistants or apprentices.

Before discussing the materials and the methods of execution now in use, it would be well to notice a great change which has taken place both in the status of the workman, the division of labour, and the mechanical appliances now at his command.

Down to recent times, joinery and cabinet making were in the hands of a number of masters in the trade, far greater in comparison to the pressure of the demand on the part of buyers than is the case at present. We have a larger society of buyers, a greater demand for the execution of large orders at a rapid rate, than was the case in former generations. On the other hand, the trade is gathered up into fewer master hands. The masters then employed a less amount of labour. They took in apprentices, many of whom remained for years with them as assistants, and the establishment was more of a family. It followed, that all members of this smaller society worked together and took part in the particular sets of chairs, the tables, cabinets, and so forth, turned out from their own house. They were, moreover, animated in a closer and truer degree by the spirit, and adopted the ideas, of a master who worked with or overlooked and advised them constantly, than could be the case in our great modern establishments. Again, though, as I have already said, the old operations by which boards, bars, and other members of wood construction are joined together, have not substantially varied since the days of Egyptians and Romans, the methods of execution have undergone a great change, owing to the introduction of machinery. The skill and training of the hand of the workman must necessarily undergo a change as well, whether for the better or the worse. The workman is relieved from the necessity of attaining an absolute accuracy in much of the ordinary but essential work of joints, mortises and other operations which can be produced with an uniform exactness by mechanical means.

The fact, also, that different engines or lathes can produce at a prodigious rate certain separate parts of many pieces of furniture, has made skilled mechanics less universal "all round" men than they were. If this combination of qualities is to be met with in provincial towns or villages, there, without doubt, the standard of excellence is a lower one.

_Materials and Execution._--The woods used for making furniture besides pines and deals, are birch and beech (used for stuffed chair-frames, couches, &c.) walnut, letter wood, Spanish and Honduras mahogany, sycamore, lime, pear, cherry of several kinds, and maple; ash, English, American, and Hungarian; oak, English, foreign, and pollard, with pieces cut from wens and sweet cedar. Turners use also plane, laburnum, yew, holly, and box. More precious woods are also used in furniture: rose-wood, satin-wood, ebony, and sandal-wood. Other rare woods are used in inlaying and marquetry.

Some of these materials, mahogany and walnut, which are much in use, are imported in vast logs, the former sometimes three feet square; when of very fine grain suited to veneers, worth 1000_l._ or more, per log.

The woods are stacked in yards, or, in London, where the space cannot otherwise be had, on platforms resting on the walls of the workshops, and fully exposed to the weather. Woods are dried after a year, or two years, according to the size of the log and nature of the wood. Oak is sometimes kept for eight or more years. When sawn into the scantlings required, it is further dried by placing the logs and planks in rooms heated by the waste steam from the engine. An American patented method of drying is to place a coil of pipes, through which exceedingly cold water is passed in the drying room, which condenses and carries off the vapours from the wood exposed to this heat. Some firms have tried this method, but, I believe, without much success.

Logs are cut up by the engine with three or more perpendicular saws at once, the teeth being set to the right and left alternately, to open a passage for the blades. More valuable woods, e.g. mahogany, are cut into thin plank by an horizontal saw. In this case the teeth are not bent, but a labourer opens the passage for the blade by lifting the plank with a wedge. As little waste of the material as possible is thus secured.

Further cutting up of the material is done by means of circular saws. Part of the saw rises through a metal table. A moveable bar is firmly screwed at one, two, or more inches from the blade, and the wood is pushed by the workman against the saw, keeping one surface against the fixed bar, so as to secure a straight cut of the thickness required. Most modern _planing_ is done by a revolving cutter, brought to bear upon the wood, which is drawn under it on an iron table, with more or less pressure, according to the quantity to be taken off the surface. Messrs. Howard have contrived a tube with a blast down it, which carries the shavings at once to the furnace, otherwise the dust made by the flying particles of wood would be unendurable.

_Mouldings_ for panelling, cornices, skirtings, &c., are cut by revolving cutters or chisels, filed to any desired shape and case-hardened. They are set in a perpendicular axle and cut horizontally, the wood being firmly pressed against the tool. The workman can gear the cutter or reverse the action, so as to make a neat finish to his work.

Formerly all such work was done with a plane, cut to the required figure, and the finishings of lines of moulding had to be carved with the hand.

_Mortising_ is done by a revolving boring tool, against which the wood to be mortised is moved by a gradual action, from side to side, and backwards and forwards, till the exact depth and width are bored out; tenons fitting these cavities are cut in another lathe, also by mechanical action.

_Turning lathes._--The legs of chairs and tables are made in lathes, the general outline being obtained by turning in the simple form. Portions of the legs are sometimes squared, and the square faces must be evenly graduated. These parts are cut as follows: the lathe and the leg in it are kept at rest, and a revolving tool--in fact, a small lathe with a perpendicular cutter in it, connected by a leather band with a spindle overhead--set in motion by the steam-engine. The workman passes this cutter carefully down the four surfaces of the portions to be squared, cutting to a given depth all down, but never losing the angle outlines originally found by the first turning. When flutings have to be cut down the legs, whether they are round or square, this is done by using a revolving cutter set with horizontal action, which passes carefully along at one level, and is geared by the joiner so as to graduate the width of each fluting, as it descends, if the diminishing size of the support or leg requires it.

Bars of chairs, edges of shelves, the stretchers (or connecting bars) under some kinds of tables, are cut into carved or other shapes by an endless band saw revolving on two rollers. The workman passes his wood along an iron table against the saw, gearing the former according to the pattern drawn on the surface.

_Fretwork_ is done with a still finer hair or watch-spring saw, of which one end can be detached from the holder and passed through a small hole in the piece of wood where the piercing is to be cut out by the saw. This could not be done by an endless saw, which can only be used to shape out edges. The best saws of this description are made by Perin, in Paris.

Watch-spring saws strained in frames have long been in use. In the steam-engine it is the wood only that is moved, and as it rests on a steady table, it gives the workman a great advantage, and should enable him to shape out his design with a delicacy only attainable with greater difficulty by the old method.

The process of _mitreing_ pieces of moulding, where they meet at an angle at a corner, is done by machinery in some houses. In the works of Messrs. Jackson and Graham, this is done by setting the pieces in a metal T square. They are carefully cut by hand, and as each piece is set in a frame geared to the angle required, and under the hand of an experienced workman, no inaccuracies are likely to occur. In cabinet-making and joinery of all kinds, the number of angles round which mouldings have to pass is very great, as anyone will see who is at the pains to notice the construction of furniture of the most ordinary kind. Any staring or opening of an oblique joint is destructive of the effect of such workmanship, as it is of the strength of the joint which is glued together, and requires absolute contact of the parts to be joined.

Much work, such as chair rails, table legs, balusters for little galleries or on a large scale, is turned and cut in the steam lathe by hand, using steam power only to turn it.

_Joinery._--The pieces of wood thus prepared are made up in many different combinations. This is the work of the joiner. In the joiners' shop of Messrs. Jackson and Graham, for instance, several benches were shown to me occupied by lengths of wall-panelling in ebony, some of the work being intended to cover the wall of a staircase; it was therefore framed in sloping lines. Each panel was a rhomboid, and none of the sides or mouldings were at right angles to each other. The mouldings had several fine strings, ovaloes, &c., all specially designed by the architect of the house--as the fittings of well-furnished houses should be. For these, special cutters had been made and fitted to the steam-moulding machine. To show the back of the panelling, the workmen turned it over. Instead of each panel being held in a groove provided in the stiles and rails, a rebate only has been cut in the frame, and the panel fits into it from the back (as the stretcher of a picture fits into a picture-frame), while iron buttons screwed into the frame pieces hold the panels firmly in their places. The object of this is to allow for the contraction of the wood with the alterations of temperature. With some woods, however well seasoned, this provision is requisite, and it is the more necessary, when more than one material is employed. In using ebony over large surfaces, it is found that the lengths required for the continuous rails cannot be procured free from knots or faults; and particular kinds of wood (pear and other material) are stained and prepared, to supplement the ebony in these instances.

The joiners put together panelling, chairs, couches, frames of tables, shelves, cupboards, and other complex pieces of furniture.

_Upholstery._--Chairs and sofas required to be stuffed are then handed over to the upholsterer, and the seats and backs are stuffed with curled horsehair, carefully arranged so as not to wear into holes. A _French edge_ is given to some stuffed seats by bringing the edges of several ridges of horsehair together, so inclined towards the upper edge, that each roll receives support from the others, which react on the pressure thus brought upon them, like springs. One would suppose that these edges were maintained by whalebone, like the stocks in which a past stiff-necked generation suffered so much. Where ribbon scrolls, tiny bunches of flowers, &c., are carved on the frames and top rails of chairs and sofa-frames, if these are to be polished only, the polishing is done before the upholstery. If _parts_ are to be gilt, or the _whole_ gilt, these operations are postponed till the upholstery is completed. So also when panelling, sideboards, bookcases, &c., are to be made up, the moulded lines which can only be conveniently hand-polished while in lengths, are treated thus before making up; and there remain only flat panels and surfaces, that can be evenly rubbed for the final polishing. In upholstered furniture, the coverings would be greased and stained, if polishing were done over or in connection with them; but in the case of gilt work, it must be left in most cases to the last, for fear of dimming or rubbing the gold during the processes of sewing, nailing, stuffing, &c.

I may remark here, that though arm-chairs, fauteuils, &c., are made in great London establishments, the manufacture of light chairs on a large scale is a special branch of the trade, and mostly carried on at High Wycombe, in the neighbourhood of which town there are extensive woods of beech, and where land and water carriage is at hand to convey these productions to London and elsewhere.

_Cabinet-making._--It is by no means easy to lay down the exact technical boundary between what I have been describing as _joinery_, and what I am now about to call _cabinet-making_. They are considered, however, as distinct branches or rather, perhaps, different operations of the trade; and in such establishments as we are discussing, the cabinet makers and joiners have their own separate workshops and benches, and corresponding separate repositories for storing and drying their woods. Every kind of work is required in making costly cabinets, bookcases, sideboards, commodes, or by whatever name we choose to call the beautiful chests, cupboards, and other artistic receptacles, tables, consoles, brackets, &c., that go to complete the requirements of our modern reception rooms.

They are seldom made with the quaint or elaborate interior fittings, such as have been alluded to in older work, but every resource is brought to bear on the external decoration. Here we come to the arts brought to bear on the ornamentation of furniture.

Let us begin with carving. Sculpture is the highest or most beautiful kind of decoration that can be applied to furniture. It can only be executed by a trained artist. To go no farther back here than the Italian and French Renaissance furniture, generally made of walnut-wood, it is the spirited and graceful sculpture that makes its _first_ great attraction. The Italian carving of this kind is the most graceful; while that of France by Bachelier and others, and much that was executed in England and Germany, being, if less graceful, always spirited and thoroughly decorative. As a general rule, sculpture so applied is _conventional_ in design and treatment, that is, we rarely see it, (except, perhaps, occasionally in little ivory statuettes, and in bas-reliefs,) strictly imitative of nature, like perfect Greek sculpture. But neither should we find strict studies from nature on Greek furniture, if we had it, except with the same limitations. The furniture made by Greco-Roman artists, and discovered at Pompeii,[6] bears witness to this assertion, such as a head, a bust, the claws of animals, sculptured on furniture generally ending in scrolls or leafwork. If a human figure is complete, it bears no real proportion to objects round it, and so on.

[6] See also Q. de Quincy, Le Jupiter Olympien.

Excellent wood sculpture used to be executed in England, from the days of Grinling Gibbon to those of Adam and the Chippendales, suited to the furniture then in fashion. I wish I could say that our furniture makers of to-day could easily, or did generally, command such talents. Ingeniously carved representations of animals and game on sideboards we sometimes see, but game 'dead' in every sense. If, indeed, Messrs. Crace, Howard, Jackson and Graham, and other firms could persuade the Royal Academicians to model for them, those artists would have to give some material amount of time to the study of how they could so effectually modify their skill as to suit the requirements and opportunities of a piece of furniture, these being quite peculiar. The French are easily our masters in this respect, but even they sacrifice good qualities proper to this kind of sculpture, in a morbid search after the softness of nature.

A curious piece of mechanism has been invented, and is in use in most large London furniture workshops, for _carving by steam_. Besides boring out and cutting away superfluous material, there is an engine for making mechanical sculpture in bas-relief, or the round. The wood is fixed on a metal table, which is moved to and fro and up and down, so as to come in contact with a revolving cutter held above it. The wood is then shaped and cut, according as it is elevated or moved. There are three or four cutters, and one piece of wood may be placed under each. Under the middle cutter, replaced by a dummy tool that does not really cut, the workman places his cast or model, and makes the dummy cutter pass over every undulation of its surface. The two or three cutters on either side cut the corresponding blocks exactly to the same depths and undulations as are followed by the blunt tool. It is a _copying machine_. That such copies, though they may pass muster, will ever have the charm of original carving, the reader shall not be asked to believe.

Certain elaborate methods of decorating and finishing woodwork must now be described, viz. those known as _inlaying_ and _marquetry_. These two processes are distinct, but marquetry furniture has often portions decorated with inlaying, as also carved ornaments and decorations of beaten, cast, or chiselled metal-work. This last addition is not generally of the same importance in our modern English woodwork that it was a century ago, and I will describe the former methods first.

_Inlaying_ means the insertion of pieces of more costly wood, stone, small discs, or carved pieces of ivory, into a less valuable material. The process is as old as any manufacture in wood working of which we possess records. Beautiful plates or blocks of ivory can be seen in the Assyrian gallery of the British museum, found at Nineveh by Mr. Layard. They are deeply cut with lotus and other leaf decorations, figures and hieroglyphics, and most of them have an Egyptian character. The ivory figures, too, have been inlaid and filled up with vitrified material. Remains of these decorations are still discernible, and the thickness of many of these pieces of ivory shows that they have been sunk bodily into woodwork of a solid character.

No such work as this can be pointed out in our London workshops, but patterns and arabesques, both of wood and ivory, are occasionally let into solid beds of wood so deeply, as to be actually mortised into the main body of the structure. This is done both by our own makers and by the French cabinet maker, Henri Fourdinois, a prize piece of whose make was bought for the South Kensington museum. It is not uncommon to insert pieces of lapis lazuli, bloodstone, and precious marbles into centres of carved woodwork, and I may call attention to the use of plates, medallions and cameos of Wedgwood, or SA"vres ware, which were frequently inlaid by Chippendale, and by the great French furniture makers, or _A(C)bA(C)nistes_, of the last century. These are used in the modern satin-wood furniture of Messrs. Wright and Mansfield, and I have lately seen a coarser material used, viz. bas-reliefs in _stoneware_, imitations of the _gris de Flandres_, by Messrs. Doulton. These last, however, may be said to be rather panels set in frames, than pieces let into cavities in wood.

_Veneering and Marquetry._--An effective method of ornamenting woodwork by the application to the _surface_ of other woods is what is known as _veneering_ and _marquetry_. The surface is in both cases covered with a thin layer of other woods, fastened on with glue and by strong pressure. Some of the panelling, table tops, and other joiner's work already described, is clothed with a thin slice of more valuable wood. This is called _veneering_. Woods such as ebony, tuya, satin-wood, palm, hare-wood, and a number more, are only to be had in small scantlings, logs a few feet long, and six or seven inches wide. Other woods, of which the grain is most beautifully marked, are cut from roots, wens, and other excrescences of the trees, to which they belong, and are only found occasionally, and in lumps of no great size. The contortions of the grain, which make them so valuable and beautiful, are owing to peculiar conditions of growth. In all these cases an inch plank of wood has to be cut into very thin slices, twelve being cut with a saw, or from eighteen to twenty-two if it is cut with a knife, as in that case no material is wasted by the opening made by a saw. These slices are laid on the surface of well-seasoned wood, and in the workshops of our great manufacturers will be seen a metal table or bed, prepared expressly for the process of veneering.